| 
  • If you are citizen of an European Union member nation, you may not use this service unless you are at least 16 years old.

  • You already know Dokkio is an AI-powered assistant to organize & manage your digital files & messages. Very soon, Dokkio will support Outlook as well as One Drive. Check it out today!

View
 

Tandberg MPS202

Page history last edited by Janine Lim 15 years, 4 months ago

Tandberg MPS202 vJ3.3 installed with Border Controller vQ6.0 using Tandberg Management Suite v11.7 and Tandberg Gatekeeper N5.1

Tested June 4, 2008

 

Conference setup: Adhoc, everything set to auto

Other Notes/Issues: Polycom VSX7000s see a fast flash full screen of themselves occasionally

 

Dialing Out to these units:

Manufacturer Unit/ Software Dialing  How To Notes on Connection Solutions/Tricks/Work Arounds
 Polycom VSX3000 v8.5 Dial IP Address    
 Polycom VSX 7000 v8.7.1 Dial IP Address    
 Polycom PVX v8.0.0.0522   Looked like it connected on MPS but didn't connect on PVX  
 Polycom Viewstation v7.5.4 Dial IP Address    
 Polycom VSX 7000 behind a V2IU      
Polycom MGC 8.0 Dial IP Address MGC needs to know the IP address of the unit dialing in  
Tandberg 800 v6.0 Dial IP Address    
Tandberg 1000 E4.1 NTCS Dial IP Address    
Tandberg 1000 B10.2 NTCS Dial IP Address    
Tandberg MXP880 vF5.2 Dial IP Address    
Tandberg MXP6000 vF6.3 Dial IP Address    
Tandberg MCU vJ4.0, conference extension   Could dial IP address of conference 1, but dialing a conference extension didn't work (putting IP*ext, putting in extension, in DTMF tones, none of those worked). Dialing IP adress with ,,,confID# in the DTMF spot should work but hasn't been tested. Note added 10/13/08 - JL.
VTEL Galaxy v2.1   Crashed the conference, everything was black for everyone  

 

 

Dialing In (216.213.254.202 x8043)

 

All of these units are not registered to a gatekeeper or on the same network as the MCU unless otherwise specified.

As a general rule of thumb, if a unit is registered to a gatekeeper, or if it's a Tandberg it has to use the entry point.

Manufacturer Unit/ Software Dialing  How To Gatekeeper and Firewall Notes on Connection Solutions/Tricks/Work Arounds
Polycom VSX3000 v8.5 Dial MPS IP##extension      
Polycom VSX3400 v8.7.1 Dial MPS IP##extension      
Polycom VSX 7000 v8.7.1 registered to Tandberg Gatekeeper Dial MPS IP##extension doesn't work but use the entry point.
Dial the IP adddress of the border controller entry point, and then # to bring up the DMTF menu, then 5 (manual entry), then conference extension, then # again.
    10/13/08, should try again with the new GK version. Should be able to call IP of the MCU, then use # and the DTMF menu. -JL
Polycom VSX 7000 v8.7.1 Dial MPS IP with extension in extension box or IP##extension      
Polycom PVX v8.0.0.0522 registered to Tandberg Gatekeeper Dial MPS IP##extension   wouldn't connect
Unregister from the gatekeeper 
Polycom PVX v8.0.2 Dial MPS IP ## extension behind V2IU and registered to Pathnavigator    
Polycom PVX v8.0.0.052 Dial MPS IP##extension      
Polycom Viewstation v7.5.4 not registered to a gatekeeper Dial MPS IP with extension in box on the far right of the IP/348/Clear row OR Put IP and extension in the address book. It dials as IP,extension      
Polycom Viewstation v7.5.4 registered to a Tandberg gatekeeper N5.2 Dial MPS IP with extension in box on the far right of the IP/348/Clear row OR Put IP and extension in the address book. It dials as IP,extension      
Polycom VSX 7000 behind a V2IU registered to a Tandberg Gatekeeper N5.2

Dial IP*extension or IP** or IP# or IP## doesn't work

Dial the IP adddress of the border controller entry point, and then # to bring up the DMTF menu, then 5 (manual entry), then conference extension, then # again.

     
Polycom VSX 7000 behind a V2IU registered to PathNavigator Dial MPS IP##extension      
Polycom MGC 8.0 Dial MPS IP and put the conference extension in the party extension       
Polycom MGC 9.0        
Tandberg 800 v6.0

Dial IP*extension or IP** or IP# or IP## doesn't work

Dial the IP adddress of the border controller entry point, and then # to bring up the DTMF menu, then 5 (manual entry), then conference extension, then # again.

     
Tandberg 1000 E4.1 NTCS Dial the IP adddress of the border controller entry point, and then # to bring up the DTMF menu, then 5 (manual entry), then conference extension, then # again.      
Tandberg 1000 B10.2 NTCS        
Tandberg MXP880 vF5.2

Dial IP*extension or IP** or IP# or IP## doesn't work

Dial the IP adddress of the border controller entry point, and then # to bring up the DTMF menu, then 5 (manual entry), then conference extension, then # again.

     
Tandberg MXP6000 vF6.3

Dial the IP adddress of the border controller entry point, and then # to bring up the DMTF menu, then 5 (manual entry), then conference extension, then # again.

  Can dial with remote access (web controlling) and extension@IP but doesn't negotiate properly resulting in a black screen.  
Tandberg MCU vJ4.0, conference extension Can't dial IP and conference number; tried a bunch of ways with # and @ and extensions, plus the extension box on the MCU.
  receiving quality degraded, more pixelation and freezing, but no packet loss reported on the endpoint.

Dial IP of the border controller entry point. Used a Polycom VSX 7000 to dial #,#,5, conference extension, # and got in. 

 

9/26/08 Try IP address in the IP field; and ,,,confID# in the DTMF field. - JL

VTEL Galaxy v2.1 Can't do DTMF or # or * or anything else.  
Type the IP address. Then hold a telephone up to the Vtel microphone and press the DTMF tones for the conference.

 

 

Comments (0)

You don't have permission to comment on this page.