-
If you are citizen of an European Union member nation, you may not use this service unless you are at least 16 years old.
-
You already know Dokkio is an AI-powered assistant to organize & manage your digital files & messages. Very soon, Dokkio will support Outlook as well as One Drive. Check it out today!
|
Tandberg MPS202
Page history
last edited
by Janine Lim 15 years, 6 months ago
Tandberg MPS202 vJ3.3 installed with Border Controller vQ6.0 using Tandberg Management Suite v11.7 and Tandberg Gatekeeper N5.1
Tested June 4, 2008
Conference setup: Adhoc, everything set to auto
Other Notes/Issues: Polycom VSX7000s see a fast flash full screen of themselves occasionally
Dialing Out to these units:
Manufacturer |
Unit/ Software |
Dialing How To |
Notes on Connection |
Solutions/Tricks/Work Arounds |
Polycom |
VSX3000 v8.5 |
Dial IP Address |
|
|
Polycom |
VSX 7000 v8.7.1 |
Dial IP Address |
|
|
Polycom |
PVX v8.0.0.0522 |
|
Looked like it connected on MPS but didn't connect on PVX |
|
Polycom |
Viewstation v7.5.4 |
Dial IP Address |
|
|
Polycom |
VSX 7000 behind a V2IU |
|
|
|
Polycom |
MGC 8.0 |
Dial IP Address |
MGC needs to know the IP address of the unit dialing in |
|
Tandberg |
800 v6.0 |
Dial IP Address |
|
|
Tandberg |
1000 E4.1 NTCS |
Dial IP Address |
|
|
Tandberg |
1000 B10.2 NTCS |
Dial IP Address |
|
|
Tandberg |
MXP880 vF5.2 |
Dial IP Address |
|
|
Tandberg |
MXP6000 vF6.3 |
Dial IP Address |
|
|
Tandberg |
MCU vJ4.0, conference extension |
|
Could dial IP address of conference 1, but dialing a conference extension didn't work (putting IP*ext, putting in extension, in DTMF tones, none of those worked). |
Dialing IP adress with ,,,confID# in the DTMF spot should work but hasn't been tested. Note added 10/13/08 - JL. |
VTEL |
Galaxy v2.1 |
|
Crashed the conference, everything was black for everyone |
|
Dialing In (216.213.254.202 x8043)
All of these units are not registered to a gatekeeper or on the same network as the MCU unless otherwise specified.
As a general rule of thumb, if a unit is registered to a gatekeeper, or if it's a Tandberg it has to use the entry point.
Manufacturer |
Unit/ Software |
Dialing How To |
Gatekeeper and Firewall |
Notes on Connection |
Solutions/Tricks/Work Arounds |
Polycom |
VSX3000 v8.5 |
Dial MPS IP##extension |
|
|
|
Polycom |
VSX3400 v8.7.1 |
Dial MPS IP##extension |
|
|
|
Polycom |
VSX 7000 v8.7.1 registered to Tandberg Gatekeeper |
Dial MPS IP##extension doesn't work but use the entry point.
Dial the IP adddress of the border controller entry point, and then # to bring up the DMTF menu, then 5 (manual entry), then conference extension, then # again. |
|
|
10/13/08, should try again with the new GK version. Should be able to call IP of the MCU, then use # and the DTMF menu. -JL |
Polycom |
VSX 7000 v8.7.1 |
Dial MPS IP with extension in extension box or IP##extension |
|
|
|
Polycom |
PVX v8.0.0.0522 registered to Tandberg Gatekeeper |
Dial MPS IP##extension |
|
wouldn't connect
|
Unregister from the gatekeeper |
Polycom |
PVX v8.0.2 |
Dial MPS IP ## extension |
behind V2IU and registered to Pathnavigator |
|
|
Polycom |
PVX v8.0.0.052 |
Dial MPS IP##extension |
|
|
|
Polycom |
Viewstation v7.5.4 not registered to a gatekeeper |
Dial MPS IP with extension in box on the far right of the IP/348/Clear row OR Put IP and extension in the address book. It dials as IP,extension |
|
|
|
Polycom |
Viewstation v7.5.4 registered to a Tandberg gatekeeper N5.2 |
Dial MPS IP with extension in box on the far right of the IP/348/Clear row OR Put IP and extension in the address book. It dials as IP,extension |
|
|
|
Polycom |
VSX 7000 behind a V2IU registered to a Tandberg Gatekeeper N5.2 |
Dial IP*extension or IP** or IP# or IP## doesn't work
Dial the IP adddress of the border controller entry point, and then # to bring up the DMTF menu, then 5 (manual entry), then conference extension, then # again.
|
|
|
|
Polycom |
VSX 7000 behind a V2IU registered to PathNavigator |
Dial MPS IP##extension |
|
|
|
Polycom |
MGC 8.0 |
Dial MPS IP and put the conference extension in the party extension |
|
|
|
Polycom |
MGC 9.0 |
|
|
|
|
Tandberg |
800 v6.0 |
Dial IP*extension or IP** or IP# or IP## doesn't work
Dial the IP adddress of the border controller entry point, and then # to bring up the DTMF menu, then 5 (manual entry), then conference extension, then # again.
|
|
|
|
Tandberg |
1000 E4.1 NTCS |
Dial the IP adddress of the border controller entry point, and then # to bring up the DTMF menu, then 5 (manual entry), then conference extension, then # again. |
|
|
|
Tandberg |
1000 B10.2 NTCS |
|
|
|
|
Tandberg |
MXP880 vF5.2 |
Dial IP*extension or IP** or IP# or IP## doesn't work
Dial the IP adddress of the border controller entry point, and then # to bring up the DTMF menu, then 5 (manual entry), then conference extension, then # again.
|
|
|
|
Tandberg |
MXP6000 vF6.3 |
Dial the IP adddress of the border controller entry point, and then # to bring up the DMTF menu, then 5 (manual entry), then conference extension, then # again.
|
|
Can dial with remote access (web controlling) and extension@IP but doesn't negotiate properly resulting in a black screen. |
|
Tandberg |
MCU vJ4.0, conference extension |
Can't dial IP and conference number; tried a bunch of ways with # and @ and extensions, plus the extension box on the MCU.
|
|
receiving quality degraded, more pixelation and freezing, but no packet loss reported on the endpoint. |
Dial IP of the border controller entry point. Used a Polycom VSX 7000 to dial #,#,5, conference extension, # and got in.
9/26/08 Try IP address in the IP field; and ,,,confID# in the DTMF field. - JL
|
VTEL |
Galaxy v2.1 |
Can't do DTMF or # or * or anything else. |
|
|
Type the IP address. Then hold a telephone up to the Vtel microphone and press the DTMF tones for the conference. |
Tandberg MPS202
|
Tip: To turn text into a link, highlight the text, then click on a page or file from the list above.
|
|
|
|
|
Comments (0)
You don't have permission to comment on this page.